What is the standard drywall thickness?

Standard Walls

And a Few Words on Drywall Thickness However, other types of drywall come in different thicknesses; the most common are 1/4 inch, 3/8 inch, 1/2 inch and 5/8 inch. Quarter-inch and 5/8-inch drywall tend to be slightly more expensive than 1/2 inch or 3/8 inch.

what is code for drywall on ceilings? Most building codes mandate either 1/2 or 5/8 inch drywall for single-thickness applications. Thinner ¼ and 3/8 inch to be used to cover existing walls and ceilings.

Also know, what is the actual thickness of 5/8 drywall?

1/2″ drywall and greenboard are exactly 1/2″ thick. 5/8drywall and greenboard are exactly 5/8” thick.

Do they make 1/4 inch drywall?

1/4inch: Not a common thickness, 1/4inch-thick drywall is used as a skimming (or double-wall) material for placing over an existing surface. 1/2-inch: Half-inch drywall panels are the standard thickness for interior walls, as well as ceilings.

Is lightweight drywall any good?

Ultra-light drywall is a generic term for drywall that is about 25% lighter than standard drywall. Weight savings is the chief positive of ultra-light boards. Other qualities that are neutral or slightly negative are the higher cost, brittle consistency, and poorer sound mitigation.

What is the difference between drywall and Sheetrock?

Drywall is a panel made of gypsum plaster pressed between two thick sheets of paper. It is used to make interior walls and ceilings. Sheetrock is a trademark for drywall made by the US Gypsum company.

What is the difference between Blueboard and drywall?

Drywall panels are covered with paper that will take paint directly, once they’ve been taped and the joints and fasteners have been covered with compound. Blueboard’s more absorbent paper layer is designed to bond with a veneer plaster coating before it’s painted.

What is the difference between green and purple drywall?

What’s the difference between PURPLE® drywall and traditional green drywall? Traditional green drywall (also known as greenboard) is only moisture-resistant. PURPLE® drywall, only made by National Gypsum, is superior because it offers moisture, mold and mildew resistance.

What is Blueboard?

Blue board drywall is also known as plaster baseboard. Blue board is used for veneer plastering, and the surface paper has special absorption qualities. It has a high water and mold resistance and there are fewer steps involved in veneer plastering. Blue board drywall is not made for mud, tape, or paint.

What can I use instead of drywall?

10 Types of Drywall Alternatives for Your Walls Lath and Plaster. Lath and plaster used to be a more time consuming wall surface to install, however, over time, the system has evolved and is now a quicker and easier form of wall to install, and makes a nice alternative to drywall. Cement Board. Plastic Panels. Concrete Walls. Wood Planks. Brick. Veneer Plaster. Pegboard.

How thick is a stud?

Rough Stud Because it has not been planed or run through a molder, it still has its original dimensions — about 2 inches in thick and 4 inches wide, though these numbers are not always uniform.

What is Type C drywall?

Type C is an industry phrase to designate enhanced gypsum panels that exceed the requirements for Type X gypsum board in ASTM C1396. Type C panels typically have a shrinkage-compensating additive, and when exposed to heat, the Type C gypsum board expands providing more fire-resistance at joints and seams.

How do you measure drywall?

Divide the total drywall square footage needed by the drywall panel square footage. If you use 4-by-8-foot panels, that is 32 square feet each. A 4-by-12-foot panel has 48 square feet. Divide the 723 square feet of drywall needed for the example room by 32 square feet to determine the number of 8-foot panels needed.

What is the thinnest drywall?

¼” Drywall: This is the thinnest sheet of drywall available. It is the ideal choice for remodeling your basement, or for any residential interior walls and ceilings that do not require thick reinforcement.

How long should drywall screws be?

When installing 1/2 inch drywall, nails or screws should be at least 1 1/4 inches long and nails should be of a ring shank variety to provide better security and reduce the chances of “popping”. 3/4 inch drywall necessitates a slightly longer 1 1/2 inch nail or 1 3/8 inch screw.

How thick is drywall in a garage?

Also, ?” is the standard thickness for fire-resistant or fire-code drywall, commonly found in garages. ¼” drywall is relatively uncommon, and can be used for repairs or for curved areas, where you can double up two sheets to make a standard ½” sheet. As far as lengths, the standard sheet size is 4′ x 8′.